Yoshizen's Blog

Sony NEX to Nikon Z homemade Mount adaptor

To use Nikon-Z camera with my system, I needed to make a mount adaptor to attach Sony NEX optics on Nikon-Z which is not available on the market.  —– If it is not there, why not to make one myself (is my motto).  Since I made so many lenses etc to use on Sony A7R, to remake them for Nikon-Z mount is too much work. 

And to have a lens comparison kind of work, there are so many mount adaptor to EOS but very few to Nikon, its mean, since I got EOS to NEX adaptor, such as Rollei to EOS, Contax to EOS, etc, and EOS to NEX, Leica to NEX then NEX to N-Z, all those lenses could be summarized on Nikon-Z . (in theory but may not be in practice. 😀 )  (So far, it seems that the N-Z7 camera can easily deal with even a dark pinhole while showing very little noise, they seems to be pretty usable and in comparison, in camera VR seems to be very effective.   (However, intentionally set M mode, 1/2 second for the test, still the result was not shaky picture —– It’s too good to be true though, it was discovered that it was not because of the VR but the shatter makes very little vibration and the lens I used (Canon 100mm macro F2.8 with proxer) happen to be very solid and steady even for handheld shooting.)

But the hidden cost of N-Z was, —– that the XQD memory card is hugely expensive and we need to buy Sony XQD card reader for a whopping cost of £40 ! —– I thought, card reader should be about £5 though, in close look both of them were rare Made in Japan, not from China or Korea but by Sony themselves ! —– then there was a second thought, wait a moment, has Sony got memory factory ? = the XQD Memory chip might come from Toshiba Yokkaichi Factory. )   😀

There is only 2 mm gap between those 2 mount. (Nikon Z got 16mm and Sony NEX is 18mm)   2 mm is so small to fill —– you may think, though it is a quite troublesome 2 mm.    Unlike M42 (Pentax screw mount), bayonet mount needs to fill many requirements.  Bayonet claws needed to have slick enough but not wobbling, tight enough spring to hold the male craw, and as it can slip off, it needs to have a secure stopper pin. etc etc.  Use Nikon F lens on Canon EOS case, the EOS mount was large enough to accommodate Nikon bayonet therefore 2.5mm gap was enough to make an adaptor. (so, we can easily get them cheap about £5 from China)   

The another trouble between NEX and N-Z is, Sony lens wouldn’t work on anywhere else, other than a Sony camera.   There is no manual focus ring, neither manual F stop control.  Attempt to use Sony lens on N-Z would be useless = forget it. —– Yet still, as all of my homemade lenses are utterly bare minimum = nothing automatic, there wouldn’t be any problem of those functions.  = as long as my optics stays there securely, I can take picture, and that is all what I need.

Base material I got for mount adaptor was a 58mm reverse adaptor for Nikon-Z from China. = This adaptor goes to Nikon side.  And to receive the bottom of Sony side was, simply a rear lens cap for Sony lens.  

Then the work starts.  They are all very very simple work = scrape off the 58mm screw part on the ring.  And to cut out the bayonet part from the lens cap.  —– Still it took nearly half day. (don’t get short-tempered = it would spoil all the effort done within a short second = Be a good Buddhist ! —– remember, even a rain drop would carve the rock)  😀    (If you got a good milling machine, even a bench drill with milling bit, such kind of work would be a matter of few minutes though the machine wouldn’t make you enlightened)   😀

 

(by the way,  the surface of the adaptor photo left, was finished with oil-stone)

Then, insert the bayonet ring of the lens cap into the N-Z adaptor ring and fix it.  (The lens on the adaptor would be as secure as how the lens cap stays on the lens = don’t expect too much —– anyhow, the cost of this adaptor was only about £6 or so) —— (and get enlightened was an option   😀  )

Voila, NEX to N-Z lens mount adaptor (though, it has no stopper pin, the heavy lens could fallen off, yet still, it works perfect with my homemade — such as 110 Pentax lens, Vest Pocket camera lens etc etc.  

Thanks goodness, I did very good job ! 

.

5 Responses

Subscribe to comments with RSS.

  1. […] reverse adapter ring for  Nikon Z, I got other idea to modify this Leiz lens.  ( Since my post of NEX to Nik Z adapter appeared, the Ring disappeared from the market — disgruntled Nikon might have bought up all […]

  2. Most useful Tool | Yoshizen's Blog said, on February 3, 2019 at 03:44

    […] I did rather miserable work with improvised Spiral Saw Blade to cut a lens cap, my patience has run-out.   Don’t dream a happy visit.  Just get on the job = get the Tool […]

  3. […] After I discovered that the lens keeps moving whether it was mounted on the Nikon (using homemade NEX to NikZ adaptor) or left alone.   So, they were the photographic evidences.  (of Sony (or Minolta) […]

  4. […] bit cynical view, this lens SEL30M35 (30mm Macro F3.5) can give more on the Nikon Z (with my special adapter) —– than on the genuine Sony body.   😀     What ever the Sony says, the lens […]

  5. […] cameras. You can see more of his creations on the Yoshizen blog. This article was also published here and shared with […]


Leave a Reply

Fill in your details below or click an icon to log in:

WordPress.com Logo

You are commenting using your WordPress.com account. Log Out /  Change )

Google photo

You are commenting using your Google account. Log Out /  Change )

Twitter picture

You are commenting using your Twitter account. Log Out /  Change )

Facebook photo

You are commenting using your Facebook account. Log Out /  Change )

Connecting to %s

This site uses Akismet to reduce spam. Learn how your comment data is processed.

%d bloggers like this: